• Now AcceptingPayPal
    0
Fasco 110 Epoxy Glue
        • Fasco 110 Epoxy Glue
        • Fasco 110 Epoxy Glue

        Fasco 110 Epoxy Glue

        Fasco 110 Epoxy Glue

        Score: 0.00 (votes: 1)
        Reviews: 1
        0.00|
        Reviews: 1
        • $34.99
         
        In stock(185 items available)
        OR

        24 pints per case

        12 quarts per case

        4 gallons per case

         

        DESCRIPTION

        110 Fas-Stick Epoxy Glue is a two-part putty type glue with an epoxy resin base. The Part 1, Resin Side is milky white. The Part 2 Hardener Side is amber. Both components are about the consistency of Vaseline. The glue that results from equally mixing the two components is the strongest yet developed by science. The following properties are characteristic:

        1. Adhesion - Unusually high adhesion to concrete, stone, wood, metal, glass, ceramic, rubber and a wide variety of plastic materials.
        2. Cohesion - When the resin is properly cured, the cohesion strength within the bond line is so strong and the adhesion of the epoxy to the materials so great that stress failure will often occur in one of the materials being bonded rather than in the epoxy.
        3. Shrinkage - Epoxy Glue cures with only a small shrinkage compared to other adhesives. As a consequence, less strain occurs at the bond line and it is stronger. Shrinkage is held to a fraction of 1%.                                                                                                                .
        4. Stability - Epoxy glue maintains its dimensions and shape under prolonged stress. The stability combined with outstanding tensile, shear and impact strength makes epoxy glue unique among adhesives.
        5. Resistance - Unlike most adhesive materials, epoxy glue is highly resistant to moisture. Its resistance to solvents is outstanding.
        6. Insulation - Epoxy glue is an excellent insulator to both heat and electric current.

        USES

        Gluing stone, concrete, glass to aluminum, foam products together, bonding trim, cabinet shops, assembly and repair of fiberglass products, body repair sealant, and many other glue applications limited only by the imagination.

        APPLICATION

        1. Make sure surface is clean, dry and sanded.
        2. Mix equal parts of Part 1 and Part 2 thoroughly. Make sure glue becomes a uniform color and there is no streaking due to insufficient mix.
        3. Apply glue to both surfaces to be joined. It is not necessary to put pressure on the glue joint.
        4. Glue takes 3-4 hours to set at room temperature. Average complete cure should take 24 hours. This will vary dependent on the mass of glue used in the joint. The thicker the glue, the faster it will set. A very thin film of glue may take in excess of 24 hours to cure. External temperature also effects hardening. The higher the temperature the faster the cure. To speed up setting of the glue, a heat lamp may be used.

        PRECAUTIONS

        Do not mix more glue than you are going to use. Once mixed, the glue will harden. When large amounts of glue are mixed, there is a short pot life in which to use the glue. A quart unit mixed at one time may gel in 10-15 minutes, which may cause considerable heat. Unless the glue can be used quickly, it is better to mix in smaller quantities or to spread the glue out before using to reduce heat generated and lengthen the pot life.

        TEMPERATURE MUST BE 65° F. OR OVER OTHERWISE WILL BE SLOW DRYING.

        For a faster set, use 110-FS Fast Epoxy Glue. This film sets in 45 minutes @ 75 degrees F.

         

        TEST RESULTS OF 110 FAS-STICK APPROXIMATE PHYSICAL CHARCTERISTICS OF FORMULATION

        Pot Life, 1 lb. mass, minutes(1)

        60

        CURED STATE PROPERTIES(2)

         

        Heat Deflection Temperature, °C.

        42

        Tensile Strength, psi

        5,250

        Tensile Elongation at break, %

        16.0

        Izod Impact ft-lb/lnch notch

        1.02

        Hardness, Shore D

        77

        Water, Absorption(3)

        0.54

        Weight Loss(4)

        0.81

        Electrical Properties

         

        Dielectric Constant(5)

        3.62

        Dissipation Factor(5)

        0.037

        Volume Resistivity, ohm-cm

         

        @ 25°C.

        8.2 (1013)

        @ 66°C.

        7.5 (109)

        @ 93°C.

        <10

         

         

        lm Equal volume ratio.

        1. Determined on 1/8" thick test specimens at 25°C. Cured for 16 hours at 25°C. followed by 2 hours at 100°C.
        2. Percent weight loss after 24 hours at 150°C.
        3. Percent weight gained after 24 hours immersion in water at 25°C.

        Determined at 105 Hertz.

         

          • SKU
            110PK
          • Weight
            1 lbs
        • Mixing Ratio
          1:1
        • Select Each or Case
          Each, Case
        • Select Kit Size
          Pint Kit (1/2 Pint of Part 1 & 1/2 Pint of Part 2), Quart Kit (1 Pint of Part 1 & 1 Pint of Part 2), Gallon Kit (1/2 Gallon of Part 1 & 1/2 Gallon of Part 2), 10 Gal Kit (5 Gallon Pail of Part 1 & 5 Gallon Pail of Part 2)
        Customer reviews
        Average rating:
        0.00(Votes: 1)
        Please sign in to add review
        • Jeffrey Engle
          Dec 31, 1969, 19:00
          Best glue I have ever used. Will buy again. Thank you for good service and fast shipping.
        To replace this text with your store's actual shipping info, go to "Design -> Menus & Pages -> Product Page Tabs" and edit the Shipping info page.

        We accept the following payment methods:

        Accepted payment methods

        To replace this text with your store's actual info on payment methods, go to "Design -> Menus & Pages -> Product Page Tabs" and edit the Payment methods page.

        This page is intended for your policy regarding returns and refunds.

        Here you can provide information as to what products can be returned, how many days your customers have to return their purchase, whether they will receive a refund in the original form of payment, a replacement or a store credit, who pays for the shipping of the previously purchased products to the store, and so on.

        To replace this text with your store's actual return policy, go to "Design -> Menus & Pages -> Product Page Tabs" and edit the Return Policy page.